Frequent question: What is required for a swept boss base in Solidworks?

There are two main requirements to create a Swept Boss or Base: A closed profile and a path. … It is important to make sure that the starting point of the path lies on the same plane as the profile. Also, notice how the center of the circle profile is centered on the start of my path.

What is swept boss Base Command in Solidworks?

Swept Boss/Base PropertyManager

  • Open a part that has either a closed profile sketch and a sketch path, or a part with a sketch line, edge or curve on the model that you can specify as a path.
  • Click Swept Boss/Base (Features toolbar).

How do you swept the boss in assembly in Solidworks?

Click Assembly Features (Assembly tab on the CommandManager) and click Swept Cut , or click Insert > Assembly Feature > Cut > Sweep . Set options as needed in the Swept Cut PropertyManager. Under Feature Scope, specify which components you want the feature to affect.

How many sketches do we need to use the feature swept boss?

The SOLIDWORKS Sweep feature has been improving over the years; unlike Extrude the Sweep feature requires at least two sketches to be selected, namely the Profile and Path.

IT IS INTERESTING:  Best answer: How do I draw two lines in AutoCAD?

How do you create a swept cut in Solidworks?

Swept Cut PropertyManager

  1. Open a part that has either a closed profile sketch and a sketch path, or a part with a sketch line, edge or curve on the model that you can specify as a path. For a solid profile, open a part that has a tool body as the profile and a sketch path to follow.
  2. Click Swept Cut (Features toolbar).

How do I create a sweep feature in Solidworks?

To create a sweep: Sketch a closed, non-intersecting profile on a plane or a face.

Click one of the following:

  1. Swept Boss/Base on the Features toolbar or Insert > Boss/Base > Sweep.
  2. Swept Cut on the Features toolbar or Insert > Cut > Sweep.
  3. Swept Surface on the Surfaces toolbar or Insert > Surface > Sweep.

What is a sweep solidworks?

SWEEP is the one feature in Solidworks that helps sweep a closed profile along a closed or open path. In this session, we are going to use a simple 3D object as an exercise to demonstrate the use of the SWEEP command in Solidworks.

How do you use the boundary boss base in Solidworks?

To open the Boundary PropertyManager, do one of the following:

  1. Click Boundary Boss/Base (Features toolbar) or Insert > Boss/Base > Boundary.
  2. Click Boundary Cut (Features toolbar) or Insert > Cut > Boundary.
  3. Click Boundary Surface (Surfaces toolbar) or Insert > Surface > Boundary Surface.

Where is sweep in Solidworks?

Click one of the following: Swept Boss/Base on the Features toolbar or Insert > Boss/Base > Sweep. Swept Cut on the Features toolbar or Insert > Cut > Sweep. Swept Surface on the Surfaces toolbar or Insert > Surface > Sweep.

IT IS INTERESTING:  What is AutoCAD ReCap?

How do you sweep a pipe in Solidworks?

To create a circular profile sweep:

  1. In a part, click Insert > Cut > Sweep to cut a tube into the part.
  2. In the PropertyManager, under Profile and Path, click Circular Profile.
  3. In the graphics area, select a curved edge for Path. …
  4. Click . …
  5. Click Insert > Boss/Base > Sweep to add the solid rod.

What is boss base in Solidworks?

One of the oldest commands in the SOLIDWORKS software is the boss/base extrude command. An Extruded Boss/Base feature will allow you to take a 2D sketch and add thickness to it in the third dimension. Every few releases, this feature gets some terrific functionality added to it.

Can you do a sweep cut in Solidworks?

Solidworks swept cut is features tool, mainly used to cut a solid model or part by sweeping a completely closed profile along an open or closed path. To use swept cut, you should need a closed profile and open or closed path, which may be line, helix, and circle, rectangular or arc etc.