How do you use the cavity feature in SolidWorks?

How do you fill cavities in Solidworks?

SOLIDWORKS make this an easy process even if the part is complex.

Filling a Mold Cavity Using Combine

  1. Open the mold assembly in SOLIDWORKS.
  2. Insert Components > New Part. Select a reference plane i.e. Top plane. Exit out of the sketch command.
  3. Insert > Features > Join. Group select all of the parts of the assembly.

How do you subtract two parts in Solidworks?

To subtract bodies:

  1. Click Combine. (Features toolbar) or Insert > Features > Combine.
  2. In the PropertyManager, under Operation Type, select Subtract.
  3. For Main Body, select the body to keep. …
  4. For Bodies to Subtract, select the bodies whose material you want to remove.
  5. Click Show Preview to preview the feature.
  6. Click .

How do I use mold tools in Solidworks?

To enable the SOLIDWORKS Mold Tools interface, right click on the Features tab (or any Command Manager tab) in the command manager and select “Mold Tools”. This will activate the Mold Tools tab.

How do you make a mold in Solidworks?

Creating a Mold Core and Cavity

  1. Open a part containing a core surface body, a cavity surface body, and a parting surface body.
  2. Select a face or plane that is perpendicular to the direction of pull. …
  3. Click Tooling Split (Mold Tools toolbar).
IT IS INTERESTING:  How do I maximize my screen in AutoCAD?

What is volume of cavity?

The cavity volume is all the volumes large enough to accommodate a solvent molecule, but that are not connected to the macromolecule exterior (Figure 3, red). Cavities are essentially isolated from the exterior, because solvent is unable to escape to the surface without any structural rearrangements.

Is there a fill feature in Solidworks?

The SOLIDWORKS Fill surface was added to the software in 2001, after surfacing was added in 1998+. It is essentially an N-sided Coons patch that will fill an opening in a surface that is otherwise closed.

How do you subtract features in Solidworks?

To subtract bodies:

  1. Click Combine. (Features toolbar) or Insert > Features > Combine.
  2. In the PropertyManager, under Operation Type, select Subtract.
  3. For Main Body, select the body to keep. …
  4. For Bodies to Subtract, select the bodies whose material you want to remove.
  5. Click Show Preview to preview the feature.
  6. Click .

How do you cut part of a part in Solidworks?

However, you can create a multibody part by using Insert Part to place one part into the other part file. Then you can use Combine on the multibody part. (Features toolbar) or Insert > Features > Combine. In the PropertyManager, under Operation Type, select Subtract.

How do I trace a part in Solidworks?

(Sketch toolbar) or click Tools > Sketch Tools > Sketch Picture. In the dialog box, browse to the picture file and click Open.

Under Trace Settings:

  1. Select a tool for Image Type.
  2. Select a tool for Selection tools, and create a border around the image you want to trace.
  3. Click Begin trace.
IT IS INTERESTING:  Your question: What is meant by Revit Architecture?

What is mold tool in Solidworks?

The Mold Tools toolbar provides tools for creating mold tooling (cores, cavities, etc.) Planar Surface. Scale. Offset Surface. Insert Mold Folders.

How do you make a casting mold in Solidworks?

The simple way of creating camera mold.

  1. First of all add Mold tool command. Open existing part.
  2. Add Scale. Scale depend on material you use. …
  3. Create Parting line. …
  4. Shut Off Surfaces, this close all gaps.
  5. Create Parting Surface. …
  6. Create Core and Cavity by Tool Split. …
  7. Enter value of Core and Cavity. …
  8. First Result.

What is Mould tool?

The mould tool is the key component in the injection moulding of plastic: It provides a passageway for molten plastic to travel from the injection cylinder (barrel) to the mould cavity. It allows the air which would be trapped inside when the mould closes to escape. … It cools the moulding until it sets.

How do you mold a body part?

Slip Latex Hand from a Life Casting

  1. Use alginate to make a mold of the hand.
  2. Melt Modeling clay and pour this into the alginate mold.
  3. Let the clay harden (put in a fridge if needed) and remove the alginate.
  4. Touch up and perfect the clay positive. …
  5. Make a two-part plaster mold. …
  6. Clean out the mold and let it dry.